| Author |
Message |
|
knightley
Firing on two.
Joined: June 19th, 2010, 8:40 pm
Posts: 761
Location: Kingswood, S.Glos.
|
 Re: What did you do with your A Series today? citroenboat wrote: Wiped Gerty all over lovingly with old engine oil to preserve the rusty finish - practiced for years on women using baby oil to perfect this technique... Known a lot of rusty women then!! 
_________________
John Jordan
It is a truth universally acknowledged, that a single man in possession of a good fortune must be in want of a d'olly.
|
| January 11th, 2015, 8:25 pm |
|
|
|
Robcap
Joined: May 10th, 2013, 1:29 pm
Posts: 24
|
Re: What did you do with your A Series today? took the manifold off, to be able to work on the carb, and to take off the air ducts and heat exchangers, to see where the oil leak comes from...
_________________
 2VC 1980, Vert Embrun
|
| January 11th, 2015, 11:17 pm |
|
|
|
Nelsthebass
Firing on two.
Joined: October 5th, 2009, 8:22 pm
Posts: 1415
Location: Stone, Staffs
|
Re: What did you do with your A Series today? Feckin Result! Celeste passed with only a few advisories and a new front number plate - best scrap heap A series yet.......
_________________
1987 2CV Special
2014 Suzuki Swift Sport
2015 Lexus NX300h
1966 Ami Break
|
| January 13th, 2015, 1:13 am |
|
|
|
citroenboat
Firing on two.
Joined: November 11th, 2010, 4:19 pm
Posts: 590
|
Re: What did you do with your A Series today? Took the 123 off Gerty and put points back, she appeared to start on both cylinders and felt 'lively' (if you can say that about a 425 with terminal compression failiure); tomorrow I will find out if she starts from cold on both... 
_________________
Mike
|
| January 15th, 2015, 12:38 am |
|
|
|
tfaerch
Firing on two.
Joined: February 9th, 2009, 11:27 am
Posts: 181
Location: Copenhagen, Denmark
|
Re: What did you do with your A Series today? Hinge rivetted to the windscreen frame:  
_________________
|
| January 19th, 2015, 12:29 am |
|
|
|
2CViking
viking bastard
Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
|
Re: What did you do with your A Series today?  Are you French  Do it again and properly 
_________________
|
| January 19th, 2015, 9:17 am |
|
|
|
wiltz
Firing on two.
Joined: June 15th, 2009, 6:08 pm
Posts: 161
|
Re: What did you do with your A Series today? Harley wrote: 3400x190x45  [URL=http://s350.photobucket.com/user/bimba101/media/Mobile%20Uploads/20150108_120155_zpsts1v7f79.jpg.html] 2400 and 2100 lengths.  [/URL]  Thanks Harley, these pictures have got me round to finely fit a hatchback set up, I've had lurking in the loft for yonks, like the rear light panel too, might pinch that idea for my hack 
|
| January 20th, 2015, 8:24 pm |
|
|
|
tfaerch
Firing on two.
Joined: February 9th, 2009, 11:27 am
Posts: 181
Location: Copenhagen, Denmark
|
Re: What did you do with your A Series today? 2CViking wrote: :roll: Are you French Do it again and properly It HAS been done properly. When we took of the old frame, the only part not rusted was behind the hinge. So I removed paint from the new frame, took of the hinge (there were allready rust behind the hinge), got it galvanized, and rivetted it on with sealant between hinge and frame.. NO welding! Airplanes are rivetted as well! Old fart!
_________________
|
| January 21st, 2015, 11:08 pm |
|
|
|
2CViking
viking bastard
Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
|
Re: What did you do with your A Series today? You obviously don't know the difference between aviation rivets and back yard shit rivets
Bastard
_________________
|
| January 22nd, 2015, 12:13 am |
|
|
|
Russell
Firing on two.
Joined: November 29th, 2008, 10:05 pm
Posts: 9259
Location: West Sussex, U.K.
|
Re: What did you do with your A Series today? Are they aluminium rivets?
_________________
samfieldhouse wrote: What I like about I2F is that there is no pretence of democracy.
|
| January 22nd, 2015, 9:46 am |
|
|
