| International2cvFriends.com http://international2cvfriends.com/forum/ |
|
| Lumenition Instructions http://international2cvfriends.com/forum/viewtopic.php?f=7&t=2200 |
Page 1 of 3 |
| Author: | bertiewhite [ September 19th, 2010, 2:33 pm ] |
| Post subject: | Lumenition Instructions |
I've just "received" a 2nd hand lumenition unit along with a bag of ignition related bits & pieces but without instructions and wondered if anybody has a set that they could either scan & email or photocopy & post please? I would like to assume that the instructions supplied with new units provide a step by step guide - am I right? |
|
| Author: | Simon Crook [ September 19th, 2010, 3:11 pm ] |
| Post subject: | Re: Lumenition Instructions |
have a look here: http://www.autocar-electrical.com/new/main.php/suppor |
|
| Author: | Neil [ September 19th, 2010, 3:20 pm ] |
| Post subject: | Re: Lumenition Instructions |
Any good? http://www.lumenition.com/PMA50ins.pdf |
|
| Author: | bertiewhite [ September 19th, 2010, 4:33 pm ] |
| Post subject: | Re: Lumenition Instructions |
Not really dudes. I saw that link to the generic instructions over on 2CVGB but a) I don't know exactly what model I've got and b) precisley what it replaces. Here's a pic of what I've got:  Am I right in assuming that the module block gets mounted away from the engine & the optical bit sits in the points box? |
|
| Author: | bertiewhite [ September 19th, 2010, 4:53 pm ] |
| Post subject: | Re: Lumenition Instructions |
Aha, I think I've answered my own question. It looks like the black plastic rotor is a push fit onto the timing cam which then "chops" the optical sensor inside the points (now removed) box. I take it the advance weights are still required to advance the timing. |
|
| Author: | Terry [ September 19th, 2010, 7:04 pm ] |
| Post subject: | Re: Lumenition Instructions |
Hi Bertie,I've got a photo-copied set here wot came with my Lumie kit.....pm me your address[unfortunately I aint got a scanner] best regards T. 
|
|
| Author: | meshking [ September 19th, 2010, 7:12 pm ] |
| Post subject: | Re: Lumenition Instructions |
Hi Bertie, I've seen the module mounted on the inner wing before, but when I fitted one to my dyane I extended the wires and put the module onto the firewall. You're spot on about the sensor and the advance weights. I'm guessing that you'll be timing this up at full advance too, so at least you can check the weights are doing what they should. Ben |
|
| Author: | 602 [ September 20th, 2010, 9:51 am ] |
| Post subject: | Re: Lumenition Instructions |
Luminition Instructions, remove from box check all components open bin chuck all items in bin search ebay for 123 ignition feel satisfied.
|
|
| Author: | bertiewhite [ September 20th, 2010, 9:59 am ] |
| Post subject: | Re: Lumenition Instructions |
602 wrote: Luminition Instructions, remove from box check all components open bin chuck all items in bin search ebay for 123 ignition feel satisfied. or alternatively 1. do your research & ask the opinions of lots of people instead of just one 2. obtain a lumenition kit for the price of the petrol it takes to collect it 3. see how you get on as you've lost nothing but time if it doesn't work out 
|
|
| Author: | 602 [ September 20th, 2010, 10:24 am ] |
| Post subject: | Re: Lumenition Instructions |
bertiewhite wrote: nothing but time if it doesn't work out I rest my case. |
|
| Page 1 of 3 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|