| Author |
Message |
|
wiltz
Firing on two.
Joined: June 15th, 2009, 6:08 pm
Posts: 161
|
 602 inlet/ exhaust manifold I'm wondering if a standard 602 manifold will fit onto a 652 visa Engine? I'm fancying the long time log jamed in the shed, but started up on a pallet on sunday 652 engine, spending a summer in the Acad. During the casual poke/look around we noticed a small section of rubber pipe jubilee clipped up on one of the inlet pipes close up to the carb mounting block, i'm not aware this was a problem when we ran the Visa, but looks as though it could be a temporary repair done by a previous owner. As I have got a really good 602 manifold, I wondered if this would be a straight swop? If not I'll leave well alone, and put it in as it is and look for another. 
|
| March 30th, 2010, 7:22 pm |
|
|
|
ken
Agony Aunt - You have a car problem? Speak to Ken
Joined: March 6th, 2009, 1:40 am
Posts: 3675
|
Re: 602 inlet/ exhaust manifold wiltz, if it makes life any easier, all Visa 2 pot manifolds are like that...  ken wiltz wrote: I'm wondering if a standard 602 manifold will fit onto a 652 visa Engine? I'm fancying the long time log jamed in the shed, but started up on a pallet on sunday 652 engine, spending a summer in the Acad. During the casual poke/look around we noticed a small section of rubber pipe jubilee clipped up on one of the inlet pipes close up to the carb mounting block, i'm not aware this was a problem when we ran the Visa, but looks as though it could be a temporary repair done by a previous owner. As I have got a really good 602 manifold, I wondered if this would be a straight swop? If not I'll leave well alone, and put it in as it is and look for another.
_________________
|
| March 30th, 2010, 7:59 pm |
|
|
|
grifftravel
Old Bloke
Joined: May 25th, 2009, 11:39 am
Posts: 685
|
Re: 602 inlet/ exhaust manifold Remember to change the clutch on it Wiltz if its the same engine I think it is.
_________________
Now known as 602
http://www.2CVTech.co.uk
|
| March 30th, 2010, 8:58 pm |
|
|
|
wiltz
Firing on two.
Joined: June 15th, 2009, 6:08 pm
Posts: 161
|
Re: 602 inlet/ exhaust manifold ken wrote: wiltz, if it makes life any easier, all Visa 2 pot manifolds are like that... ken Thanks Ken, it just looks home made.
|
| March 30th, 2010, 10:45 pm |
|
|
|
wiltz
Firing on two.
Joined: June 15th, 2009, 6:08 pm
Posts: 161
|
Re: 602 inlet/ exhaust manifold grifftravel wrote: Remember to change the clutch on it Wiltz if its the same engine I think it is. Yes Paul I bet you can still smell it, I did put a clutch in the following week,we ran the car for a few more months after that, but then it got the chop for want of a clutch cable, sad really.
|
| March 30th, 2010, 10:50 pm |
|
|
|
wiltz
Firing on two.
Joined: June 15th, 2009, 6:08 pm
Posts: 161
|
Re: 602 inlet/ exhaust manifold Yes Ken I've( or rather Annie's) found it, page 80 photo 7.3 Haynes Visa manual.
|
| March 30th, 2010, 11:22 pm |
|
|
